Flyers
Mon-Fri 7am-1am EST Sat-Sun 8am-11pm EST
1(888)985-6937
Mon-Fri 7am-1am EST Sat-Sun 8am-11pm EST
My Store: | Change | Find A Store  
X
Store #
Phone:
Fax:
Hours:
Monday - Friday
Saturday
Sunday
masterPageBottomBannerImg
Home > Projects & DIY Toolkit > Mother's Day Gift - Oak Serving Tray

Mother's Day Gift - Oak Serving Tray

PAMPER MOM WITH A GIFT MADE FROM THE HEART

Oak Serving Tray

Oak Serving Tray

Carry food and drinks in style with this colourful, easy-to-make serving tray you can build in a weekend using simple tools and materials.

Steps

  1. Cut a piece of 1/2-in-thick oak plywood 13-in long and 17-in wide for the base (A). (The grain should run from front to back, not side to side.) If you don't have a table saw, ask a Lowe's associate to make the cut for you in the store. Sand both sides of the tray with 120-grit and 180-grit sandpaper.
  2. From 1/2-in x 2-in oak, cut two end pieces (B) that match the 13-in width of the plywood base. Glue and clamp the ends (B) to the base (A) with the ends and edges flush. Let dry about two hours. Good to Know: By the cutting the end pieces to fit the base, you'll reduce gaps between the end pieces and the front and back pieces.
  3. Measure between the outside faces of the ends (B) and cut the front and back (C) to that length (about 18 inches). Glue and clamp the front and back to the base (A) and ends; let dry.

Apply Stain and Paint Stripes

  1. Sand the tray sides with 120-grit and 180-grit sandpaper. Wipe the surfaces clean and apply a coat of stain (We used Cabot oil-based stain tinted Moonshadow). Let the stain dry before the next step. Good to Know: It's possible to apply a latex paint over an oil-based stain if the stain has dried thoroughly. If you don't notice any solvent odour coming from the wood, the stain is dry enough to paint.
  2. Use a square as a guide to mark light pencil lines defining the width of the painted stripes. The stripes shown vary from 1/2-in to 1-3/4-in wide. Apply painter's tape around the inside faces of the tray ends, front, and back. Then apply tape beside the pencil lines and paint between the tape strips. After the paint dries, remove the tape.

MATERIALS

  • 2 - 1/2-in x 2-in x 4-ft red oak board
  • 1/2-in x 2-ft x 4-ft oak plywood
  • Cabot oil-based stain, half pint
  • Minwax satin polyurethane, 8 ounces
  • Valspar Signature paint
  • Fabulous Red (#1011-2)
  • Pale Cordovan (#3010-7)
  • Field of Pines (#5004-4A)
  • Hacienda Tile (#2010-4)
  • Jekyll Grand Dining Sea Mist (#5005-3c)
  • Red Ochre (#2011-4)

TOOLS

  • Miterbox and saw
  • Clamps with 18-in capacity
  • 120-grit, 180-grit sandpaper
Your Recently Viewed Items
You have no recently viewed items. After viewing product detail pages or search results, look here to find an easy way to navigate back to products you are interested in.
Your Recommended Items

You currently have no recommended items. Browse a few more items to give us an idea of what you like.
sitelink
© 2012 - 2016 Lowe's ®. All rights reserved. Lowe's and the gable design are registered trademarks of LF, LLC v2.4.0.46 release/EV2.4
1001
Server: WWW85 Created On: 12/3/2016 3:38:21 AM